The Sprue In Wax Pattern Should Be Placed______
The Sprue In Wax Pattern Should Be Placed______
At Right Angle | |
At 45°C Angle | |
At Obtuse Angle | |
It Depend Upon Type Of Wax Pattern |
پاک اسٹڈی لائبریری اپنی خدمات کو بہتر کرنے کے لئے نئے سوفٹ وئیر انسٹال کررہی ہے ۔ اس لئے آئندہ کچھ دن آپ کو کچھ صفحات تک رسائی میں مشکلات کا سامنا ہوسکتا ہے ۔ جس کے لئے ہم معذرت خواہ ہیں۔
Pak Study Library is installing new software to improve its services. herefore, in the next few days, you may face difficulties in accessing some pages. sorry for the inconvenience.
The Sprue In Wax Pattern Should Be Placed______
At Right Angle | |
At 45°C Angle | |
At Obtuse Angle | |
It Depend Upon Type Of Wax Pattern |
The Solvent Flux Used For Base Metal Soldering Is______
Fluoride | |
Borax | |
Rouge | |
Boric Acid |
The Solid Solution Of Silver And Mercury Is Called______
Y1 | |
B1 | |
Y | |
Y2 |
The Simplest Alloy Is A______
Eutectic Alloy | |
Ternary Alloy | |
Peritectic Allowy | |
Solid Solution |
The Setting Time Of Znpo4 Cement Can Be Retarded By______
Slower Addition Of Powder To Liquid | |
Mixing More Powder To The Liquid | |
Faster Addition Of Powder To Liquid | |
Mixing Powder To Liquid, Checked By Water |
The Setting Time Of Irreversible Hydrocolloids Can Be Decreased By______
Using Excess Water For Maxing | |
Raising The Temperature Of Water Used For Maxing | |
None Of The Above | |
Lowering The Temperature Of Water Used For Mixing |
The Setting Of Zinc Phosphate May Be Retarded By ?
Decrease The Addition Of Powder To Liquid | |
Diluting The Liquid With Water | |
Increase The Addition Of Powder To Liquid | |
Increased In The Ratio Of Powder To Liquid |
The Setting Of Zinc Phosphate Is Accelerated By______
Adding A Drop Of Water | |
Cooling The Slab | |
Adding A Drop Of Oleic Acid | |
Increasing Mixing Time |
The Setting Expansion Of Gypsum Products Can Be Reduced By______
Allowing Setting Under Water | |
Increased Spatulation | |
Adding Potassium Sulfate | |
Less Water Powder Ratio |
The Role Of Magnesium Chloride In Zinc Oxide Eugenol Impression Paste______
Plasticier | |
Accelerator | |
Modifier | |
Retarder |
The Restoration Which Shows Percolation And Shrinkage Along The Margins Is______
Composites | |
Polycarboxylate | |
Amalgam | |
Unfilled Resins |
The Relative Hardness Of Elastomere Is Determined Using______
Rockwell Tester | |
Barcol Indenter | |
Knoop Pyramid | |
Shore Durometer |
The Rate Of Tarnish And Corrosion Of Class Ii Cast Material Having Vhn 200 Is______
2 To 3% | |
<1% | |
0% | |
5 To 10% |
The Rapid Decrease In Tensile Strength And Increase In Ductility Of A Wrought Metal Is Seen In Which Stage Of Annealing ?
Grain Growth Stage | |
Recovery Stage | |
Recrystallisation Stage | |
All Of The Above |
The Ranking Of Tear Strength From The Lowest To Highest Of All Impression Materials Generally Is As Follows______
Polysulfide, Hydrocolloids, Silicones, Polyether | |
Silicones, Hydrocolloids, Polyether, Polysulfide | |
Hydrocolloids, Silicones, Polyether, Polysulfide | |
Hydrocolloids, Polyether, Silicones, Polysulfide |
The Purity Of Gold Is Expressed In______
Fineness | |
Percentage | |
Carats | |
Gram |
The Pure Form Of Gold Used In Dentistry Is Known As______
Cohesive Gold | |
Class Iv Casting Gold | |
Non Cohesive Gold | |
Class I Casting Gold |
The Proportional Limit Is Defined As______
The Maximum Stress That Can Be Induced Without Permanent Deformation | |
The Maximum Elongation Under Tension That Can Be Measured Before Failure | |
The Minimum Force Required To Cause A Structure To Break | |
The Maximum Stress In A Structure |
The Product, Which Is Obtained By Calcining Gypsum Under Steam Pressure At 120-130°C Or By Dehydrating Gypsum In The Presence Of Sodium Succinate Is___
Calcium Sulphate Dihydrate | |
Alpha – Hemihydrates | |
Beta – Hemihydrates | |
Orthorhombic Anhydrate |
The Process Wherein Two Or More Chemically Different Monomers, Each With Some Desirable Property, Can Be Combined To Yield Specific Physical Properties
Addition Polymerization | |
Copolymerization | |
Step-Growth Polymerization | |
Condensation Polymerization |
The Process Of Changing The Rubber Base Product Or Liquid Polymer, To A Rubber Like Material Is Generally Known As______
Boiling | |
Chain Lengthening | |
Condensation | |
Vulconization |
The Principle Application Of Zinc Phosphate Cement Is______
It Has Less Occlusal Wear | |
In Final Cementation | |
As A Temporary Filling Material | |
As Temporary Cementation |
The Principal Constituent Of Set Silicate Cement Matrix Is______
Hydrate Aluminosilicate Gel | |
Hydrated Aluminium Phosphate | |
Hydrated Aluminium Phosphate Crystal, Caf2 Alluminosiliate Gel | |
Hydrated Aluminium Phosphate With Calcium Fluoride |
The Preferred Material For Repair Of Fractured Denture Base Is______
Chemically Cure Resin | |
Vinyl Resin | |
Heat Curve Resin | |
Light Cure Resin |
The Porosity Formed Due To Simultaneous Nucleation Of Solid Grains And Gas Bubbles At The First Moment That Metal Freezes At The Mold Walls Is Called___
Subsurface Porosity | |
Micro Porosity | |
Gas Inclusion Porosity | |
Pinhole Porosity |