Which Of The Following Releases Single Wavelength Of Energy ?
Which Of The Following Releases Single Wavelength Of Energy ?
Argon Lasers | |
Led | |
Pac | |
Qth |
پاک اسٹڈی لائبریری اپنی خدمات کو بہتر کرنے کے لئے نئے سوفٹ وئیر انسٹال کررہی ہے ۔ اس لئے آئندہ کچھ دن آپ کو کچھ صفحات تک رسائی میں مشکلات کا سامنا ہوسکتا ہے ۔ جس کے لئے ہم معذرت خواہ ہیں۔
Pak Study Library is installing new software to improve its services. herefore, in the next few days, you may face difficulties in accessing some pages. sorry for the inconvenience.
Which Of The Following Releases Single Wavelength Of Energy ?
Argon Lasers | |
Led | |
Pac | |
Qth |
Which Of The Following Refractory Is Used To Counteract Most Of The Expansion______
Quartz | |
Tridymite | |
Corundum | |
Cristobalite |
Which Of The Following Provide Opacity To Composite ?
Ti02 | |
Bis-Gma | |
Tegdma | |
None Of The Above |
Which Of The Following Properties Of Dental Materials Is Time Dependent______
Resillience | |
Elastic Limit | |
Creep | |
Ultimate Strength |
Which Of The Following Procedure Is Indicated To Produce Cross-Linking In The Polymerization Of Linear Chains Of Acrylic______
Incorporation Of Terminating Agents | |
Increasing The Amount Of Heat Required For Linear Polymerization | |
Addition Of Grain Refining Agents | |
Addition Of Difunctional Monomers |
Which Of The Following Physical Property Can Be Used To Estimate Indirectly The Proportional Limit Of Gold Alloys ?
Rockwell Hardness Number | |
Vickerss Hardness Number | |
Knoop Hardness Number | |
Brinell Hardness Number |
Which Of The Following Phases Of Dental Amalgam Has Minimum Strength______
Epsilon 1 | |
Gamma 3 | |
Gamma 2 | |
Gamma 1 |
Which Of The Following May Result If An Excessive Amount Of Monomer Is Incorporated Into An Acrylic Resin Mixture ?
Excessive Shrinkage | |
Excessive Brittleness | |
Low Impact Strength | |
Excessive Expansion |
Which Of The Following Is Used As Surface Hardener In Impression Material ?
2% Sodium Sulfate | |
4% Potassium Sulfate | |
0.2% Potassium Sulfate | |
2% Potassium Sulfate |
Which Of The Following Is True About Direct Filling Gold______
None Of The Above | |
Whatever May Be The Type Voids Are Inherent | |
Voids Can Be Avoided With Manual Condensation | |
Properly Condensed Mat Gold Has No Voids |
Which Of The Following Is True About Agar Hydrocolloid Impression Material ?
Cannot Register Fine Surface Details | |
Liquefies Between 71 – 100°C | |
Solidfies Between 50 – 70°C | |
Facilitates Fabrication Of Metal Dyes |
Which Of The Following Is The Main Constituent Of Porcelain______
Feldspar | |
Quartz | |
Kaolin | |
Clay |
Which Of The Following Is Present In The Powder Of The Acrylic Resin______
Hydroquinone | |
Benzoyl Peroxide | |
D-Methyl Paratolouidine | |
Methyl Methacrylate |
Which Of The Following Is Not True Of Polymethyl Methacrylate ?
Knoop Hardness Number 18 To 20 | |
Tensile Strength Of 60 Mpa | |
Modulus Of Elasticity Of 3.4 Gpa | |
Density Of 1.13 G/Cm3 |
Which Of The Following Is Not True About Elastomeric Impression ?
Single Mix Material Have Higher Viscosity | |
Shear Thinning Is Related To Viscosity Of Non Phase Impression Material | |
Putty – Wash Technique Of Impression Reduces Dimensional Change Of Setting | |
Improper Mixing Of Material Can Cause Permanent Deformation Of Impression |
Which Of The Following Is Not Affected By Saliva ?
None Of The Above | |
Impression Plaster | |
Impression Paste | |
Silicon Impression Material |
Which Of The Following Is Most Important In Strength Zoe______
Temperature Of Mixing Stab | |
Liquid Powder Ratio | |
Speed Of Mixing | |
Addition Of Few Drops Of Water |
Which Of The Following Is Function Of Fluoride Flux In Soldering Process ?
It Prevents The Formation Of Chromium Oxide Or Dissolves Chromic Oxide Layer | |
Increase The Strength Of Solder | |
It Prevents The Flow Of Material In Undesirable Area | |
It Prevents The Formation Of Copper Oxide |
Which Of The Following Is Correct Regarding Chemical Setting Of Condensation Silicone______
By Condensation Of Repeated Molecules Of Monomers | |
Polymerization Occurs With Repeated Elimination Of Small Molecules | |
Polymerization Occurs With Elimination Of Single Byproduct | |
Condensation Does Not Occur At All |
Which Of The Following Is Correct Glass Transition Temperature Of Impression Compound ?
100°C | |
65°C | |
43.5°C | |
39°C |
Which Of The Following Is Correct Arrangement Of Impression Material Regarding Linear Contraction In Ascending Order ?
Addition Silicone < Polyether < Polysulfide < Condensation Silicone | |
Condensation Silicone < Polyether < Polysulfide < Addition Silicone | |
Condensation Silicone < Polysulfide < Polyether < Addition Silicone | |
Addition Silicone < Polysulfide < Polyether < Condensation Silicone |
Which Of The Following Is Common To Both Zinc Eugenol Cement And Polycarboxylate Cement?
Substitution O Eugenol By Eba To Increase Strength Of Cement | |
Chelation | |
Polyacrylic Acid Is Liquid | |
Chemical Bond To Tooth Structure |
Which Of The Following Is An Example Of A Composite Material ?
Colloidal Silica | |
A Filled Resin | |
Gold Alloy | |
Wax |
Which Of The Following Inhibitor Accelerator System Uses Light Activation Composite ?
Peroxide-Amine | |
Organic Acid-Peroxide | |
Diketone-Amine | |
Organic Acid-Metal Oxide |
Which Of The Following Increases Castability Of Base Metal Alloys______
Molybdenum | |
Carbon | |
Beryllium | |
Tin |